A 4-wheel drive is a type of vehicle that has four wheels and two axles, the front axle can be powered by the engine or the engine can be connected to the rear axle. When the 4-wheel drive is engaged, the vehicle can move in any direction from a standing position.
The 2004 Chevy Silverado is equipped with a 4-wheel drive transmission but engaging it gives more power to the vehicle. In case you are not sure how to engage 4-wheel drive on your 2004 Chevy Silverado, read on to find out.
How to Engage 4 Wheel Drive Chevy Silverado 2004
Chevy Silverado is such a vehicle which is featuring a 4 wheel drive system that allows you to take your truck off-road or through deep snow with ease. This system is engaged when you turn the knob on the center console to the four-wheel drive position.
To engage 4 wheel drive chevy Silverado 2004, the first thing is to make sure that your Silverado is neutral. After that, you then engage the parking brake and you put your foot on the brake pedal.
Now, shift the transfer case to move into a low range and it will allow the ease of flow and engage the feature. The final step to complete the process is to turn the knob on your dash to engage the front axle and that’s all.
NOTE: it is important to note that the 4 wheel drive system should only be made use of when it is necessary. So using it unnecessarily can cause wear and tear on the system and can decrease fuel efficiency.
Silverado 4 Wheel Drive System – Explained
Silverado 4 wheel drive system is a system that features an engine that allows you to take your truck off-road or through deep snow with ease. The engine is powerful and efficient which makes it a great choice for towing or hauling.
This system is engaged when you turn the knob on the center console to the four-wheel drive position. The suspension of two engines is top-notch which provides a smooth ride even when the terrain is rough.
The engine horsepower of the Silverado 4 wheel drive system is between 285 and 305 capacity rate. While the towing capacity is between seven thousand and eight thousand pounds for most needed.
The maximum speed that you can drive in a four wheel drive Silverado is about 55 mph speedway ability. This speedometer level of the vehicle prevents damage to the system and helps to maintain fuel efficiency.
Watch Video Guide
On The Blog
How to Put 2005 Chevy Silverado in 4 Wheel Drive
2005 chevy Silverado four-wheel drive always sends power to all four axles which occur at once. The four-wheel drive in Chevy Silverado provides the Silverado with more traction in terms of hazardous conditions.
So to put the 2005 chevy Silverado in 4 wheel drive, put the Silverado on neutral mode first and put the Silverado parking brake. The next step is for you to put your foot on the brake pedal as well.
Then, you shift the transfer case and put it into the low range of the vehicle to aid in putting the Silverado successfully. The last thing to do so as to complete the process of turning the knob on your dash to put in the front axle and that’s all.
Do You Have to Be in Neutral to Switch to 4wd?
YES, actually for you to switch your chevy Silverado four-wheel drive to 4wd there is a need for you to put the system in neutral. Some older and more basic 4wd systems must be engaged manually with the vehicle.
In switching the system to 4wd, the system needs to be engaged manually with the vehicle at a complete stop and transmission in park or in neutral mode. It is actually risky to be in motion and make the switching process.
So don’t try to switch to 4wd while engaging with the four wheel drive systems when the vehicle is in motion. By doing so the expensive components of the vehicle can actually be damaged.
Though in a typical way, you can actually switch the system to 4wd at any time while driving your vehicle. But it is advisable to switch it to 4wd when going in slow motion and in a straight line movement.
Is It Bad to Shift from 2wd to 4wd While Driving?
NO, it’s not bad switching the vehicle system from 2wd to 4wd while driving, just make sure that the vehicle is on slow speed and in a straight line driving. In that mode, you can do the switching which is helpful on different roads with limited traction.
It is very easy to shift between two wheel drive (2wd) and four wheel drive (4wd) in your car while in motion. And for you to do that, first slow your vehicle down to a crawling form like 1-3 mph.
After the above process, you then switch your transmission into neutral mode and turn the transfer control case which is the shifter that controls 2wd and 4wd. Put the shifter in the desired position and put the vehicle back to gear and that’s all.
Can You Switch from 2h to 4h While Driving?
YES, you can surely switch your vehicle system from 2h to 4h while driving, and can also be done when not driving. It is possible for you to move the control from 2h to 4a or 4h at a stop or while driving depending on when you want to do so.
Just note that when making the switching process, you may actually hear some kind of noise when the system eventually shifts or engages in the activities. S don’t be afraid or panic as it is a normal way or signal of switching.
In the United States, there are about 6.5 million truck drivers. The trucking industry is one of the largest employers in the country with a total of over 3.4 million people employed in some capacity by trucking companies.
With such a large number of employees, it is not surprising that many drivers have to work more than 40 hours per week. The problem is that most U.S. states limit driving time to 10 hours per day and 50 hours per week on average, which means that drivers often need to rest for at least 10 hours before they can resume their shift again. This can be difficult because most drivers have only one day off each week and the rest of their days are spent working or driving around without any breaks in between shifts.
Conclusively, to engage 4 wheel drive chevy Silverado 2004, the first thing is to make sure that your Silverado is neutral. After that, you then engage the parking brake and you put your foot on the brake pedal.
Now, shift the transfer case to move into a low range and it will allow the ease of flow and engaging the feature. The final step to complete the process is to turn the knob on your dash to engage the front axle and that’s all.