How to Remove Glove Box Chevy Malibu

The glove box is a storage compartment located on the dashboard of the car. It is used to store important materials such as insurance papers, registration documents, and other personal items.

Removing the glove box is a quick and easy way to get to the screws that hold the dash and console in place. So let’s answer the question and learn how to remove the Glove Box on a Chevy Malibu.

 

How to Remove Glove Box Chevy Malibu

 

The Chevy Malibu has a glove box that can be opened by using a key. In order to remove the glove box, you need to open it with a key and then use your hands to pull it out.

Another way to remove the glove box of a chevy malibu, check the sides of the box and you will see a small white plastic block of about half-inch diameter cylinder. The cylinder is protruding from the side of the plastic block.

Also, the cylinder snaps into a hole I’m the sheet metal that is fixed on the structural side of the panels. The box will be open so you take a wide flat blade screwdriver and insert it to the tip which is between the plastic block and the metal side of the panel.

Now, you lightly press the plastic block until the cylinder is clear of the hole, and then pull the right side of the glove box towards you. Note that after the above process, the box will come out of the dashboard and the glove box chevy malibu removed.

But for you to reinstall it back to the vehicle’s system, just push the box into place until the plastic block or cylinder engages the holes in the metal side of the panels. With that, the glove box chevy malibu will be reinstalled.

 

Video Guide

 

How Much Does It Cost to Fix a Broken Glove Box?

 

A glove box is such that is used in the boot of the car which sits parallel to the rear of the vehicle. In the description of it, it has a ring at one end and a pin that locks into place and prevents it from sliding out.

To fix it replace a broken glove box, it will cost you fees of around 350 that are in USD so it can be converted to naira as well. But if you need only a small part to be replaced, which includes a latch or handle. You will actually get much much cheaper than repairing or replacing the full broken glove box.

 

 

In addition to the cost of fixing a broken glove box, you need to visit auto repair shops, and charges with be attached to the fixing labor work. Charges are between 47 UDD and 215 USD which is per hour of labor so make the estimation in naira.

Note that the cost of fixing a glove box varies which depend on the maker and of the model of the car. A single part of the box can just be replaced with little amount compared to the whole broken glove box.

 

On The Blog

How to Disable Immobilizer on Mazda 6

How to Turn off KeySense in Chrysler Pacifica

How to Open Ford Focus Parcel Shelf Clip

How to Calibrate Toyota Corolla 2014 Touch Screen

How to Reset Parking Sensors on Mercedes

 

How Do You Fix a Glove Box That Won’t Close?

 

You may be wondering why a glove box will not close and because of the difficulty encountering it, you may want to fix such an issue. Actually the reason for such is that you might have accidentally overloaded your box which makes it hard to close.

So to fix a glove box that won’t close, just identify some items popping out too high that prevent the latch mechanism from making contact with the catch. Then remove the excess items and repack the remaining items and now you can close the glove box.

 

 

Note that a glove box damper device is such that disclose having a camera rotationally movement against a spring to allow slowing the descent of glove box lid opening. The device is helpful and easy to install.

 

How Do You Fix a Glove Box Hinge?

 

A glove box hinge is present in the car to secure some paperwork which includes car paper or any other necessary paper present with you in the car. With the help of the glove box, papers are safe to carry along in the car anywhere.

To fix a glove box hinge, get quick glue and apply it to fix the glove box temporarily, then take a piece of metal and bend it to make a hinge-like structure. If the hinges eventually broke, you can possibly adjust it to lock and make it useful.

But if your lock broke out of the glove box hinge, then you have not actually accessed the glove box properly and need to do so. It’s because the glove box always assembles the lock upside and drops down to open.

Note that the hinges are important for the glove box to keep making use of it because it keeps locking the glove box in one place. It also helps in providing a motion in a particular manner.

 

What Does a Glove Box Damper Do?

 

A glove box damper is a device that is disclosed with the attachment of a camera rotational movement against a spring to slow the descent of the glove box. During the opening, the device slows the glove box lid.

 

 

You can easily install the glove box damper device and enjoy the benefit of it on your glove box tool. Apart from the easy installation process, it reduces cost and breaking ability so with that you can get it.

Not that glove box systems are designed to physically contain a sample, specimen, or product while still allowing someone to work with the materials. Glove boxes protect users in terms of hazardous or infectious agents.

 

How Do You Install a Glove Box Damper?

 

NOTE: You can easily install the glove box damper device and enjoy the benefit of it on your glove box tool. Apart from the easy installation process, it reduces cost and breaking ability so with that you can get it.

To install a glove box damper, get a glove box hinge, get quick glue, and apply it to fix the glove box temporarily. Now you then take a piece of metal and bend it to make a hinge-like structure.

 

Conclusion

 

Conclusively, to remove the glove box chevy malibu, check the sides of the box and you will see a small white plastic block of about half inch diameter cylinder. The cylinder is protruding from the side of the plastic block.

Also, the cylinder snaps into a hole I’m the sheet metal that is fixed in the structural side of the panels. The box will be open so you take a wide flat blade screwdriver and insert it to the tip which is between the plastic block and the metal side of the panel.